Glass Cloth Tape for Coil Wrapping: A Practical Application Guide

Choosing glass cloth tape for a coil wrap involves more than matching a temperature figure. The tape must fit the assembly, handle the production process and perform alongside the winding wire, varnish, resin and other insulation materials.

Use the CGS glass cloth tape product page to compare grades and specifications. This guide focuses on the practical questions to resolve before ordering slit rolls or starting a production trial.

Start with the job the tape must do

Identify the function and location of each wrap. A protective coil outer wrap, a lead hold-down and a banding operation can place different demands on the tape.

  • Coil outer wrapping: define the coverage, finished dimensions and exposed surfaces.
  • Lead holding: identify where the tape bonds, the direction of any load and the geometry around the lead exit.
  • Banding or protective wrapping: establish what must remain in position through handling and subsequent processing.

For electrical insulation applications, check the complete assembly requirements. UL Solutions describes an electrical insulation system as a combination of materials evaluated for compatibility at specified temperatures. A tape’s individual temperature or dielectric figure does not establish approval for every coil design. See UL’s explanation of electrical insulation systems.

Map the production sequence before selecting the adhesive

Write down when the tape is applied and what happens afterward. Tape applied before varnish impregnation encounters a different process from tape applied after the assembly has cured.

Resolve these questions with the selected grade’s technical data:

  • Does the tape contact varnish, resin, cleaning chemicals or process fluids?
  • Is it expected to hold the wrap before curing, after curing, or both?
  • What temperatures and exposure times occur during production and in service?
  • Does the assembly call for a standard adhesive or a thermosetting version?

Keep service temperature separate from curing temperature and time. For assemblies specifying a thermosetting adhesive, compare CGSTAPE-6458T thermosetting acrylic and CGSTAPE-6358T thermosetting rubber. Use the instructions for the exact grade and the assembly’s approved process when establishing the application and cure sequence.

Check the installed build at overlaps and lead exits

Use total tape thickness, including adhesive, when reviewing clearance. The glass cloth backing thickness alone does not describe the installed tape.

Also check locations where more than one layer is present. Overlaps, wrap terminations and lead exits can create a greater local build than the main wrapped surface. Confirm that the completed assembly still fits its housing, bobbin or adjacent components.

Specify the required overlap and number of layers in the assembly instructions. There is no single overlap percentage suitable for every mechanical and electrical design. For help interpreting electrical figures, read how to read dielectric strength and insulation specifications.

Run a representative wrapping trial

A useful trial follows the intended production sequence on the actual surface and geometry:

  1. Prepare the bonding surface. Check that the surface is sound, clean and dry using the preparation method approved for the substrate and tape.
  2. Apply the specified wrap. Use the intended tape width, layer count, overlap and application method. Record difficulty around corners, lead exits and changes in section.
  3. Run the production cycle. Include the planned varnish, resin, heat treatment and handling steps where applicable.
  4. Inspect the result. Look for gaps, wrinkles, edge lifting, displacement and excessive local build. Complete the electrical and mechanical checks required by the assembly specification.

Record the grade, roll dimensions, preparation, process conditions and acceptance criteria. This makes the result useful when the wrap is transferred to production or a material change is reviewed.

Use trial observations to refine the wrap

Observation What to review
Edges lift or the wrap shifts Surface condition, contact pressure, application method, part geometry and adhesive compatibility with the process.
Wrinkles or uncovered areas appear Tape width, the wrapping path and the overlap specified around corners and lead exits.
The assembly no longer fits Total tape thickness, layer count, overlapping sections and wrap terminations.
The wrap changes during curing The actual time and temperature profile, varnish or resin contact, and instructions for the selected adhesive grade.

Review the cause before adding more tape or changing to a thicker backing. Additional layers also change the finished dimensions.

Keep coil wrapping and temporary masking requirements separate

A coil wrap commonly remains in the assembly. Temporary masking has an additional requirement: removal after the process. For thermal spray masking, selection also considers the spray process, exposure and component geometry. A tape selected for a permanent electrical wrap should not automatically be treated as a removable masking grade.

Specify a roll format that suits production

CGS offers glass cloth tape in a standard 40-inch-wide × 36-yard-long roll format, with custom slitting to the required width. Custom roll lengths can also be made.

For a quotation, include the CGS part number, finished width, roll length and quantity. Include width tolerances and the wrapping method where they affect the finished roll. For material selection support, add the assembly drawing or wrap location, production sequence, operating conditions and any required insulation-system designation.

Explore CGS glass cloth tape options

Request a quote for your glass cloth tape requirements.

Shopping Cart
Scroll to Top